Skip to content

How to calculate HAVS exposure

Count the time each tool is running in someone’s hands. Then add every tool that person uses.

  1. Find each tool’s trigger time. That is the time it is running in the hands, not the time spent on the job.
  2. Turn it into points. Points are 2 × vibration² × hours, with the vibration in m/s².
  3. Add every tool that person uses that day. Compare the total with 100 points, the exposure action value, and 400 points, the exposure limit value.
Lesson figures. Breaker 10 m/s² and vibration-reduced plate compactor 5 m/s², round numbers inside HSE’s ranges for these tools. HSE’s recommended initial value for a breaker is 14 m/s². Where the figure comes from

One person’s morning, 07:30 to 12:00

One operative breaks out a long strip of concrete yard, lays a duct and reinstates the trench.

  1. 07:30Mark out15 min
  2. 07:45Break out the concrete1 h 15 min, breaker running 30 min
  3. 09:00Dig out and barrow away45 min
  4. 09:45Tea break15 min
  5. 10:00Lay the duct15 min
  6. 10:15Backfill and compact in layers1 h 45 min, compactor running 1 h
On the job
4 h 30 min
Trigger time
1 h 30 min

The tools ran in the hands for 1 h 30 min of the 4 h 30 min on the job. That is 30 min of breaker in short bursts and 1 h of compactor. Only this time goes into the sum.

Showing the whole morning.

Count only the time the tool is running

Trigger time is how long the hands are on the tool while it is vibrating. It may be only a few minutes in several hours of work with the tool. In the lesson’s morning the breaker is out for 75 minutes and runs for about 30.

How to find it on site

People are unlikely to estimate their own trigger time accurately. Watch the work for about half an hour and scale it up to the whole task or shift. For a repeated job, such as drilling holes, time a few and multiply by the number done in a shift.

A longer watch gives a better estimate. Time each tool the person uses, not only the one that seems worst.

From HSE, Vibration risk assessment.

Half an hour of breaking out, watched

08:01 to 08:31, one square a minute. Hatched squares are minutes with the breaker running.

12 ÷ 30
12 running minutes in 30 watched is 40%.
40% × 75
40% of the 75 minutes breaking out is 30 minutes.
About 30 min
The breaker’s trigger time for the morning.

Why double the vibration gives four times the points

Points follow the square of the vibration. At the same trigger time, twice the vibration gives four times the points.

Draw the vibration as the side of a square. Double the side and the square holds four of the small ones. Each small square here is 50 points, which is 5 m/s² for one hour.

That is why one tool can outweigh the rest of a day. In the lesson the breaker runs for half as long as the compactor and still gives twice the points.

50

50 points 5 m/s² for one hour

50505050

200 points 10 m/s² for the same hour

2 × 5² × 1 hour = 50 points2 × 10² × 1 hour = 200 points5 and 10 m/s² are the lesson figures for the compactor and the breaker.
Points for one hour of trigger time
Vibration, m/s²34567101215
Points an hour1832507298200288450

HSE’s own table rounds these to 20, 30, 50, 70, 100, 200, 300 and 450. Multiply by the hours of trigger time.

From HSE, Vibration risk assessment.

Add up every tool one person uses

Points belong to the person, not the tool. Work out each tool’s points from its trigger time, then add them for that person’s day. The lesson’s morning comes to 150 points. Nothing vibrating is used after 12:00, so that is the whole day. A tool used in the afternoon would add to it.

Breaker, lesson figure 10 m/s²

50505050an hour× ½ hour =5050the morning

200 points an hour × ½ hour = 100 points.

Compactor, lesson figure 5 m/s²

50an hour× 1 hour =50the morning

50 points an hour × 1 hour = 50 points.

150 points for the day

The morning in order
TimeWhat happenedAddsRunning total
07:45 to 09:00Breaker, 30 min trigger time at the lesson figure of 10 m/s²100100
09:45 to 10:00Tea break. No new points, and none taken away.0100
10:15 to 12:00Vibration-reduced plate compactor, 1 h trigger time at the lesson figure of 5 m/s²50150

What 150 points asks of the employer

150 is above the exposure action value of 100 and below the exposure limit value of 400.

  • Reduce exposure to as low as is reasonably practicable.
  • Provide health surveillance, which applies at or above 100.
  • Give information, instruction and training on the risk and how it is controlled.
  • Never let the day go above 400. It is a limit, not an allowance to use up.

Below 100 the risk still has to be reduced to the lowest level reasonably practicable. Some people develop symptoms at low exposures, and anyone who already has HAVS needs protecting below 100 too.

From HSE, Hand-arm vibration at work (INDG175).

The same day as eight steady hours

HSE also writes daily exposure as A(8), the steady vibration that would give the same exposure over eight hours.

√(150 ÷ 16) = 3.06 m/s² A(8)

The action value is 2.5 m/s² A(8), which is 100 points. The limit value is 5 m/s² A(8), which is 400 points.

From HSE, The hand-arm vibration exposure calculator.

How a change in the work changes the points

Halving the vibration quarters the points an hour. So half the vibration for twice the time gives half the points, and for four times the time the same points.

Two ways to do the same job, with figures made up for the comparison.

One way

Vibration
10 m/s²
Trigger time
1 h
50505050

200 points

Another way

Vibration
5 m/s²
Trigger time
2 h
5050

100 points

If the other way took 4 hours

Vibration
5 m/s²
Trigger time
4 h
50505050

200 points

HSE names two ways to cut exposure, less vibration reaching the hands and less time holding the vibrating tool. Work out the points both ways before choosing.

From HSE, Hand-arm vibration at work (INDG175).

Where the vibration figure comes from

The same work gives very different points depending on the figure used. The same 30 min of breaking out comes to anything from 49 to 324 points across HSE’s range for breakers.

HSE’s figure
A typical figure and range for each type of tool. Breakers run from 7 to 18 m/s², with 14 as HSE’s recommended initial value.
The maker’s declared figure
From the tool’s handbook, measured in a standard test. Check it represents how the tool is used. Some of this data underestimates vibration at work substantially.
A measurement
Taken on the tool as it is used on the job.
The breaker’s 30 min at four figures, against 100 and 400 points.
7 m/s²bottom of HSE’s range49
10 m/s²the lesson figure100
14 m/s²HSE’s recommended initial value196
18 m/s²top of HSE’s range324

At HSE’s recommended initial value of 14 m/s², the breaker alone is 196 points and the lesson’s morning 246. The calculator starts from HSE’s figure and takes a maker’s declared figure or your own instead.

From HSE, Vibration risk assessment.

What to write down

Record each tool’s figure and trigger time, and where each came from. Then the points, the day’s total and what that level asks. Anything needed to comply with the law goes in an action plan, with what has been done, what will be done, a timetable and who is responsible.

The lesson’s morning as a record
ToolVibration figureTrigger timePoints
Breaker10 m/s²Lesson figureAbout 30 minHalf an hour watched, scaled to the 75 minutes breaking out100
Vibration-reduced plate compactor5 m/s²Lesson figure1 hSix runs of 10 minutes, timed50
The day3.06 m/s² A(8)1 h 30 min150

From HSE, Vibration risk assessment.

Work out your own day

Enter each tool and its trigger time. The calculator uses HSE’s figures or makers’ declared figures and adds up the day.

The example opens in a new tab, so a day you are working on stays as it is.